This form has not been tested for accuracy yet. Be sure to verify the comonent specifications yourself before ordering.

Change any quantities to the numbers you want, and click the button to send your order to Digi-Key. If the default quantities are used, the price for a 'MegaView parts kit' should be $80.32, as of July 2003.

Quantities are as required for MegaView , except where minimum order quantities are required. In these cases, the minimum is ordered, with the required quantity in (brackets).

To order complete the following steps:

1. Verify that you have the quantities you want for each item below.

2. Then send your order to Digi-Key:

   (Go to Ordering Homepage and "CREATE NEW ORDER" if you want to start over with an order after you have submitted it.)

3. You will be redirected to Digi-Key to verify your order, payment method, and shipping details.
   • If you are not ordering any components for the relay board (and have already ordered for the MegaSquirt^® EFI Controller, if desired), then finalize your order by clicking on the 'finish order' button on the Digi-Key site and following the instructions there.
   • If you are also purchasing parts for the relay board, return to the MegaSquirt ordering page without finalizing your order.

Qty.	MegaView Reference	Description	Digi-Key P/N	Unit Price	Ext. Price per kit
		Vacuum Flourescent Display		58.80	58.80
		32.768 KHz Crystal		0.42	0.42
		MAX232CPE		3.31	3.31
		LM7805 Voltage Regulator		0.48	0.48
		DB-9 Male		2.33	2.33
		Power block terminal, 2 contacts		0.72	0.72
<7>		Capacitor, 0.1 uf		0.119	1.19
		Capacitor, 0.033 uf		0.18	0.18
		Capacitor, 0.01 uf		0.14	0.14
		Capacitor, 47 pf replaces 50 pf		0.81	0.81
		Capacitor, 20 pf		0.74	0.74
		Capacitor, 22 uf tantalum replaces 33 uf		2.64	5.28
		1N4001 diode		0.26	0.52
(1)		10k Resistor		0.056	0.28
(1)		100k Resistor		0.056	0.28
(1)		10M Resistor		0.056	0.28
		6-pin,1 row PCB Header (0.10")		0.42	0.42
(8)		Alum. hex standoffs, 1/2", 4-40, male to female		0.386	3.86
Sub- total	Shipping and processing may be extra, depending on your location and order size				$80.32
Here are the other parts you'll need to build your MegaView:			Some MegaSquirt® Related Links:
Printed Circuit Board (PCB) & processor - group buy 4 momentary pushbuttons 1 Bezel - instructions for fabrication are on the MegaView site. parts for cable to connect pushbuttons to the PCB. You may be able to scrounge a conector for the pushbutton header JH1 from an old computer, they often used in 2 postion configurations for microswitches, indicator LEDs, etc. Nylon Screws - 4/40 - P/N H546-ND - 0.0910ea. & Nylon Nuts - 4/40 - P/N H616-ND - 0.105ea. You need 5 of each, but there is a 100 minimum quantity for each from Digi-Key. You can try to find them locally. Look for them in hooby shops that sell radio control hardware. You CAN substitute steel screw hardware. Just be careful to make sure the metal screws do not short anything out.			MegaSquirt Site MegaSquirt Forums MegaSquirt FAQ

The JH1 header (WM6406-ND) may not be in stock at Digi-Key. You may be able to pick it up locally. It is a 1-row, 6-position straight header with a 0.100" (2.541mm) pitch. Look up the datasheet on the Digi-Key site for more details.